Government jobs • Exam updates • PreparationIndependent information portal
RojgarRankYOUR NEXT STEP STARTS HERE
Current Affairs

Andhra Pradesh Launches 177-House 3D Concrete Printing Pilot under PMAY-G 2.0

By Published

Andhra Pradesh launched a pilot on 4 October 2026 to build 177 rural houses using 3D concrete printing in two Guntur district villages under PMAY-G 2.0. Here are the verified facts, the funding split, what is still unconfirmed and the exam-relevant context.

On this page
Andhra Pradesh Launches 177-House 3D Concrete Printing Pilot under PMAY-G 2.0 — title card
RojgarRank title card.

Andhra Pradesh launched a pilot on 4 October 2026 to build 177 houses using 3D concrete printing in Burripalem and Obulnayudupalem villages, Tenali Mandal, Guntur district. The houses come under Pradhan Mantri Awas Yojana-Gramin (PMAY-G) 2.0. The source describes the project as India's first pilot housing project using this technology. That "first" claim comes from a single secondary source and is not independently confirmed here. The report was published on 5 October 2026, the day after the launch.

Key facts at a glance

ItemReported detail
Launch date4 October 2026 (source published 5 October 2026)
Number of houses177
LocationBurripalem and Obulnayudupalem villages, Tenali Mandal, Guntur district, Andhra Pradesh
SchemePMAY-G 2.0, the rural housing component of the Pradhan Mantri Awas Yojana
Estimated outlay₹13.93 crore, excluding taxes
Union Ministry of Rural Development share₹9.44 crore
Andhra Pradesh government share₹4.49 crore
Technical partner namedCSIR-Central Building Research Institute (CSIR-CBRI), Roorkee
Expected completionWithin six months of the launch date

The two shares add up to the stated outlay (₹9.44 crore + ₹4.49 crore = ₹13.93 crore). The Union Ministry of Rural Development therefore covers roughly two-thirds of the estimated cost.

What is 3D concrete printing?

3D concrete printing is an additive construction method. A computer-controlled printer deposits a cement-based material layer by layer to form a structure. It is also described as additive manufacturing in construction.

Why builders are interested

Officials quoted in the source say a house can be completed in about 10 days with this method, which they contrast with longer timelines for conventional masonry. The source does not say whether the 10 days covers only the printing or the whole house, and it gives no house size or specification. Treat the figure as an official claim, not a measured result of this project.

Background from research

A 2019 paper in Automation in Construction (from TU Dresden, Germany) is not about the Andhra Pradesh project. It does give general technical context. It describes layer-by-layer deposition by extrusion as the most mature of several additive concrete approaches. It also links interest in the technology to low productivity and skilled-labour shortages in construction. The authors note that large-scale on-site printing raises engineering challenges in printhead design, material behaviour and printing strategy. This suggests that results from a pilot depend on the specific machine, material and site conditions.

Status as of 5 October 2026

StatusItem
CompletedThe project launch on 4 October 2026, as reported.
Expected, not yet reported as doneCompletion of all 177 houses within six months of launch. No houses are reported as finished, so this is a target.
Status unclearThe tripartite MoU among the Union Ministry of Rural Development, CSIR-CBRI and the Andhra Pradesh government. The source says it "was planned", and it does not confirm that it has been signed.

Why it matters for exam preparation

The story links several topics that current-affairs and general-studies sections often cover: a flagship housing scheme, a state-Centre funding split, a technology application and a CSIR laboratory. This does not mean a question will appear in any exam. These are the points the evidence supports.

Facts worth noting

  • PMAY-G is the rural housing component of the Pradhan Mantri Awas Yojana, and this pilot is under PMAY-G 2.0.
  • Tenali Mandal is in Guntur district, Andhra Pradesh.
  • CSIR-CBRI, Roorkee, is a constituent laboratory of the Council of Scientific and Industrial Research. It works on building materials, structural engineering and construction technologies.
  • Funding: ₹9.44 crore from the Centre and ₹4.49 crore from the state.

Quick arithmetic, with a caution

Dividing ₹13.93 crore by 177 houses gives roughly ₹7.9 lakh per house. This is only a rough average. The source does not say what the outlay includes (for example, equipment, research support or site work), so it should not be read as a confirmed per-house cost.

What the evidence does not tell us

  • It does not name the printer, the contractor or the exact material mix.
  • It does not give house size, design or how beneficiaries were chosen.
  • It does not say who formally launched the project.
  • Claims of greater durability and longer lifespan than conventional rural housing are stated as design aims. No test data or standards are cited.
  • The project details rest on one secondary news source, so confirmation from an official government release would strengthen them.

FAQ

When was the Andhra Pradesh 3D-printed housing project launched?

The source reports the launch on 4 October 2026 and was itself published on 5 October 2026.

Where will the 177 houses be built?

In Burripalem and Obulnayudupalem villages of Tenali Mandal, Guntur district, Andhra Pradesh.

Who is paying for it?

The estimated ₹13.93 crore outlay (excluding taxes) is split between the Union Ministry of Rural Development (₹9.44 crore) and the Andhra Pradesh government (₹4.49 crore).

Are the houses finished?

No completion is reported. The houses are expected to be completed within six months of the launch date.

← Back to Current Affairs